Reproduction Parts

AC593 or C1646R Button Lugs - "For hay field use.  Provide sufficient traction for ordinary conditions with minimum damage to sod.  General Purpose Tractor Serial number No. 200111 and up; Wide-Tread Tractor Serial No. 400000 and up; Orchard Tractor Serial No. 0-15000 and up."  These were also used on A, AO, AOS, AR, AW, AWH, AWN, B, BO, BR, BW, BWH, BNH, and D.  Click link for picture.  Cost is $5 each and includes mounting hardware.  Shipping extra.

AC470 or C1294R/C1295R Meadow Lugs - "Meadow lugs made of channel steel with upright legs only 5/8- inch high.  Provide necessary traction in hay fields without damage to crops.  General Purpose Tractor Serial number No. 200111 and up; Wide-Tread Tractor Serial No. 400000 and up; Orchard Tractor Serial No. 0-15000 and up." Click link for picture.  Cost is $325 per set (12 left and 12 right).  Uses your existing 3/4" carriage bolts.  Shipping extra.

AC643 Swinging Drawbar - "Pivoted ahead of rear axle in center of cross bar extending between chain housings.  Permits short and easy turning with loads such as a disk harrow or similar implements.  Wide-Tread Tractor Serial No. 400000 and up."  Clink link for picture.  Cost is $400.  Shipping extra.

AC410R Muffler and Spark Arrestor - "This materially reduces exhaust sound of the engine and also prevents the escape of sparks, which is especially advantageous when tractor is operate in dry grain fields or around farm buildings.  It attaches to the regular exhaust pipe.  General Purpose Tractor Serial No. 200111 to No. 223802 inclusive; Wide-Tread Tractor Serial No. 400000 to No. 402039 inclusive.  Muffler and spark arrestor regular equipment on later tractors."  Only 15 of these will be made.  Click link for picture.  Cost is $650 for complete muffler assembly.  Shipping extra.

AC99 Front Wheel Extension Rims - "Front wheel extension rims are desireable for work in swamps and very muddy land.  Attached to the regular wheel by bolts and clamps.  General Purpose Tractor Serial No. 200111 and up."  These are 24" diameter and were used on AO, AW, BO, BR, BW.  Click on link for picture.  Cost is $600 for complete assembly including mounting clips and hardware.  Shipping extra.

AD195 Front Wheel Extension Rims - "Front wheel extension rims are desireable for work in swamps and very muddy land.  Attached to the regular wheel by bolts and clamps.  Used on D Tractor Serial No. 30400 and up."  These are 28" diameter and were used on AR.  Click link for picture.  Cost is $625 for complete assembly including mounting clips and hardware.  Shipping extra.

C740R Front Axle Pivot Pins - Used in the belly pan.  Holds the wishbone and the front axle.  Made .010 oversize from hard steel (non threaded).  Cost is $65 each.  Shipping extra.

AC918 Road Bands - Used on GPWT  tractors with skeleton or flat steel.  Also used on AR tractors over flat steel.  Purpose was for transport on roadways while keeping lugs off the road.  Click link for picture.  Cost is $625 for bands, brackets, and rivets.  Shipping extra.

AC337 Road Bands - "Driving tractors with spade lugs or grousers on finished roads is prohibited by law in some states.  AC337 road bands meet the requirements of state laws as to proper width.  Can be easily put on or taken off.  Fits over any type of lug equipment.  Gives traction similar to a smooth tire.  It increases the diameter of the rear wheel 10 inches, and therefore road speed materially."  These were used on AR flat steel also.  Click on link for picture.  Cost is $400 and includes mounting brackets and rivets.  Riveting done for $75 for a set of bands.  Shipping extra.

C1038R Washer, Cover Cap Screw - Used on the transmission cover and early engine cover.  Also used on styled G tractors.  8 or 16 were used on GP and 8 were used on G tractors.  Click link for picture.  Cost is $1 each.  Shipping extra.

Guide Bands or Skid Rings - "Guide bands are used on front wheels to assist steering by preventing the front end from slewing when turning sharp corners.  The AC650 guide bands, 2-1/2 inches high, are furnished and recommended as regular equipment, but in conditions of loose top soil, sand and dry mulch, the AC347 guide bands 3-1/2 inches high are recommended."  Click on link for picture.  Diameters available are 22", 24", and 28".  Other sizes available on request.  Cost is $115 for 22", $120 for 24", and $125 for 28".  Shipping extra.

GPWT Fender Brackets - Used on Wide-Tread Tractors Serial No. 400000 and up.  These are ONLY the brackets.  Sheet metal available from other vendors.  Click on link for picture.  Cost is $350 per pair and includes rivets.  Riveting done for $75 for a set of brackets.  Shipping extra.