Home GP Rally III Parts for Sale Tractors for Sale Restorations Tips
Consignment Items Our Schedule Our Pictures Contact Us Links
Reproduction Parts
GPWT Drawbar - holes drilled, twisted correctly. $550. Shipping Extra.
P Drawbar - holes drilled, twisted correctly. $550. Shipping Extra.
GPWT and P Front Steel - HA684A casting number. Correct for early WT's, specifically designed for model P tractors. $2500. Shipping Extra.
AC593 or
C1646R Button Lugs - "For hay field use. Provide sufficient
traction for ordinary conditions with minimum damage to sod. General
Purpose Tractor Serial number No. 200111 and up; Wide-Tread Tractor Serial No.
400000 and up; Orchard Tractor Serial No. 0-15000 and up." These were
also used on A, AO, AOS, AR, AW, AWH, AWN, B, BO, BR, BW, BWH, BNH, and D.
Click link for picture. Cost is $6 each and includes mounting hardware.
Shipping extra.
AC470
or C1294R/C1295R Meadow Lugs - "Meadow lugs made of channel steel
with upright legs only 5/8- inch high. Provide necessary traction in hay
fields without damage to crops. General Purpose Tractor Serial number No.
200111 and up; Wide-Tread Tractor Serial No. 400000 and up; Orchard Tractor
Serial No. 0-15000 and up." Click link for picture. Cost is $325 per
set (12 left and 12 right). Uses your existing 3/4" carriage bolts.
Shipping extra.
AC643
Swinging Drawbar - "Pivoted ahead of rear axle in center of cross bar
extending between chain housings. Permits short and easy turning with
loads such as a disk harrow or similar implements. Wide-Tread Tractor
Serial No. 400000 and up." Clink link for picture. Cost is $450.
Shipping extra.
AC410R
Muffler and Spark Arrestor - "This materially reduces exhaust sound of
the engine and also prevents the escape of sparks, which is especially
advantageous when tractor is operate in dry grain fields or around farm
buildings. It attaches to the regular exhaust pipe. General Purpose
Tractor Serial No. 200111 to No. 223802 inclusive; Wide-Tread Tractor Serial No.
400000 to No. 402039 inclusive. Muffler and spark arrestor regular
equipment on later tractors." Only 15 of these will be made.
Click link for picture. Cost is $650 for complete muffler assembly.
Shipping extra.
AC99 Front
Wheel Extension Rims - "Front wheel extension rims are desireable for
work in swamps and very muddy land. Attached to the regular wheel by bolts
and clamps. General Purpose Tractor Serial No. 200111 and up."
These are 24" diameter and were used on AO, AW, BO, BR, BW. Click on
link for picture. Cost is $600 for complete assembly including mounting
clips and hardware. Shipping extra.
AD195
Front Wheel Extension Rims - "Front wheel extension rims are desireable
for work in swamps and very muddy land. Attached to the regular wheel by
bolts and clamps. Used on D Tractor Serial No. 30400 and up."
These are 28" diameter and were used on AR. Click link for picture.
Cost is $625 for complete assembly including mounting clips and hardware.
Shipping extra.
C740R
Front Axle Pivot Pins - Used in the belly pan. Holds the wishbone and
the front axle. Made .010 oversize from hard steel (non threaded).
Cost is $65 each. Shipping extra.
AC337
Road Bands - "Driving tractors with spade lugs or grousers on
finished roads is prohibited by law in some states. AC337 road bands meet
the requirements of state laws as to proper width. Can be easily put on or
taken off. Fits over any type of lug equipment. Gives traction
similar to a smooth tire. It increases the diameter of the rear wheel 10
inches, and therefore road speed materially." These were used on AR
flat steel also. Click on link for picture. Cost is $550 and
includes mounting brackets and rivets. Shipping extra.
C1038R
Washer, Cover Cap Screw - Used on the transmission cover and early engine
cover. Also used on styled G tractors. 8 or 16 were used on GP and 8
were used on G tractors. Click link for picture. Cost is $1 each.
Shipping extra.
Guide
Bands or Skid Rings - "Guide bands are used on front wheels to assist
steering by preventing the front end from slewing when turning sharp corners.
The AC650 guide bands, 2-1/2 inches high, are furnished and recommended as
regular equipment, but in conditions of loose top soil, sand and dry mulch, the
AC347 guide bands 3-1/2 inches high are recommended." Click on link
for picture. Diameters available are 22", 24", and 28".
Other sizes available on request. Cost is $140 for 22", $145 for
24", and $150 for 28". Shipping extra.
GPWT Fender Brackets - Used on Wide-Tread Tractors Serial No. 400000 and up. These are ONLY the brackets. Sheet metal available from other vendors. Click on link for picture. Cost is $375 per pair and includes rivets. Riveting done for $75 for a set of brackets. Shipping extra.